Shotgun Accessories

Shotgun Accessories

SureShell Carrier for Remington 870/1100/11-87

SureShell Carrier for Remington 870/1100/11-87

SureShell Carrier for Remington 870/1100/11-87
Click to enlarge image(s)
The Mesa Tactical product line is designed for very serious law enforcement and military applications where equipment failure is not an option. The receiver mounting scheme of our Receiver Mount shotgun SureShell shotshell carriers for the Remington 870/1100/11-87 depends on steel fasteners threaded into steel pins for more secure attachment to the shotgun. The mounting plate even features a window over the shotgun serial number location, to make it easier for armorers to inventory their weapons. Made in USA
Remington 870/1100/11-87 Saddle Rails

Remington 870/1100/11-87 Saddle Rails

Remington 870/1100/11-87 Saddle Rails
Click to enlarge image(s)
Mesa Tactical Saddle Rails comprise aluminum brackets that wrap around the top of the shotgun receiver. The factory trigger pins are replaced by internally thread steel pins, to which both sides of the saddle rail are securely bolted. SureShell Saddle Rails feature a MIL-STD-1913 Picatinny sight rail along the top, and a four-, six- or eight-shot SureShell shotshell carrier yoke on the left side of the receiver.
Mesa Tactical Side Saddle for Mossberg

Mesa Tactical Side Saddle for Mossberg

Mesa Tactical Side Saddle for Mossberg
Click to enlarge image(s)
The receiver mounting scheme of our receiver mount shotgun SureShell shotshell carriers for the Mossberg 500/590/835 substitutes a steel bolt for the trigger pin retained in place by a black oxide plated acorn nut. At the front of the mounting plate, custom retaining steel hardware is used with an elongated extractor screw and a machined key hole In the plate. The mounting plate was designed not to obscure the receiver serial number to make it easier for armorers to inventory their weapons.

SureShell shotshell carriers for the Mossberg fit on the left side of the receiver only. You must use a tactical forend that does not significantly overlap the receiver, or a factory forend that is cut down appropriately. SureFire forends will work fine with no alterations.

UTG 870 Tactical Shotgun Mount

UTG 870 Tactical Shotgun Mount

UTG 870 Tactical Shotgun Mount
Click to enlarge image(s)
Fits RM 870 Shotgun and Variants
Precision Machined from Aircraft Aluminum with Maximum Strength
Low Profile with See-through Feature and V-cut on Top Rail, 14 Picatinny Slots on Top
Simple and Friendly Installation, No Gunsmith or Tool Required
Solid Locking Features for Most Secure Fit
Ultimate Tactical Solution to Enhance Accuracy under Toughest Environments
Hard Anodized Finish for Wear Resistance
Shotgun Tactical Scope Mount

Shotgun Tactical Scope Mount

Shotgun Tactical Scope Mount
Click to enlarge image(s)
Excellent quality and easy to install
Weaver/Picatinny Style, tactical low profile for all scope applications
5.5 inches (140mm) long with 13 slots on
rail to allow for flexible eye relief adjustments
Complete with screws for installation on
Mossberg 500 Series and compatibles
Shotgun Tri-Rail Barrel Mount

Shotgun Tri-Rail Barrel Mount

Shotgun Tri-Rail Barrel Mount
Click to enlarge image(s)
Shotgun Tri-Rail Barrel Mount Complete with Flashlight Clamping Feature - Each Rail with 3 Slots
Remington 870 MAG EXTENSION: 7-ROUND

Remington 870 MAG EXTENSION: 7-ROUND

Remington 870 MAG EXTENSION: 7-ROUND
Click to enlarge image(s)
Increase mag capacity to 7 rounds. Made of virtually indestructible, glass-filled nylon injection-molded over a stell connecting nut.
Will not rust or dent. New spring and instructions. Minimum barrel length for 7 shot extension is 18-1/5".
Made in USA by Advanced Technology
Remington 870 MAG EXTENSION: 8-ROUND

Remington 870 MAG EXTENSION: 8-ROUND

Remington 870 MAG EXTENSION: 8-ROUND
Click to enlarge image(s)
Increase mag capacity to 8 rounds. Made of virtually indestructible, glass-filled nylon injection-molded over a stell connecting nut.
Will not rust or dent. New spring and instructions. Minimum barrel length for 8 shot extension is 20".
Shotgun MAGAZINE CLAMP

Shotgun MAGAZINE CLAMP

Shotgun MAGAZINE CLAMP
Click to enlarge image(s)
May be used to mount mag extensions (see below) or 1 inch diameter flashlights or lasers to barrel.
Injection molded from indestructible, black, glass-filled nylon. Fits all 12GA and 20GA barrels
Made in USA by Advanced Technology
TACTICAL SHOTSHELL HOLDER

TACTICAL SHOTSHELL HOLDER

TACTICAL SHOTSHELL HOLDER
Click to enlarge image(s)
Five additional 12 GA shotshells are easily accessed from the elastomeric polymer shotshell holder. Shell holder adapts easily to mounting plate, which provides a secure attachment to the buttstock. Backplate and shell-holder can be mounted on right or left side of buttstock. Designed for right or left handed shooters, it is specially engineered for the SHOTFORCE AR-15 Buttstock. Unconditional Lifetime Warranty.
Made in USA by Advanced Technology
Shotgun Barrel Mount

Shotgun Barrel Mount

Shotgun Barrel Mount
Click to enlarge image(s)
• Solid Aluminum Construction with Matte Black Finish
• Smart 2 Piece Design for Clamping Shotgun/Paintball Barrel
• Length: 1.6" (3 slots)
• Compatible Firearm Barrel Range: Diameter.75"-1.1"
HEATSHIELD

HEATSHIELD

HEATSHIELD
Click to enlarge image(s)
Made from formed steel. Elongated cooling slots allow maximum, quick dissipation of heat for ultimate protection against burns. Easily adapts to most 12 GA. shotguns. Black oxide finish matches shotgun components
SHOTGUN REAR PISTOL GRIP

SHOTGUN REAR PISTOL GRIP

SHOTGUN REAR PISTOL GRIP
Click to enlarge image(s)
Designed with an ergonomic, textured grip for maximum control and comfort. Features include an integral top-mounted sling loop and slimmer style. Made of black glass-filled nylon, it is virtually indestructible, and backed by an Unconditional Lifetime Warranty. Fits 12 & 20 Gauge Mossberg 500/590/835, Maverick 88, Remington 870, and Winchester 1200/1300 pump shotguns. Norinco 98 Series-Law Enforcement Only
Made in USA by Advanced Technology